Update sequence for vSphere 5.5 and its compatible VMware products

http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=2057795

 

Update sequence for vSphere 5.5 and its compatible VMware products (2057795)

Purpose

VMware has made available certain releases to address critical issues for several products including:

  • vCloud Director (VCD)
  • vCloud Networking and Security (VCNS) (formerly vShield Manager)
  • Horizon View
  • vCenter Server
  • vSphere Replication (VR)
  • vCenter Site Recovery Manager (SRM)
  • vCenter Operations Manager (vCOPS)
  • vSphere Data Protection (VDP)
  • vSphere Storage Appliance (VSA)
  • ESXi
  • vShield Edge
  • vShield App
  • vShield Endpoint

This article only encompasses environments running vSphere 5.5 and VMware products compatible with vSphere 5.5.

In an environment with vSphere 5.5 and its compatible VMware products, follow the update sequence described in the Supported Update Sequence table.

Note: This article refers only to the latest versions of VMware products that are supported by vSphere 5.5 and its update sequence. For a complete list of VMware products compatible with vSphere 5.5, see VMware Product Interoperability Matrixes.

Resolution

This table describes the sequence in which the vSphere 5.5 and its compatible VMware products must be updated:

Supported Update Sequence

  VCD VCNS View Composer View Connection Server VSA Manager vCenter Server VR / SRM vCOPS VDP ESXi VMware Tools vShield Edge vShield App vShield Endpoint View Agent / Client
Update Sequence Number 1                            
  2                          
    3                        
      4 4**                    
          5*                  
            6 6 6            
                  7*          
                    8        
                      9 9 9 9

* If you are using a Cisco Nexus 1000V, see vSphere 5.5 and its compatible third-party products in the Additional Information section of this article before upgrading vCenter Server (sequence step 5) or the ESXi hosts (sequence step 7).

Note: If you need to update multiple products in your environment, start with updating the product with the lowest sequence number. After you update the product, update the product with the next sequence number. If a product is not present in your environment, update the subsequent product. If you need to update two products with the same sequence number, the order of update does not matter.

Before you update vCenter Server, disable vCenter Server from vCloud Director. Also ensure that you stop or disable other VMware services so that they do not communicate with vCenter Server during the update process. For more information, see the product documentation.

Sample VMware product upgrade scenarios

Example 1

If you have the vCloud Director solution stack installed in your environment, the supported patch update sequence is:

  1. Update vCloud Director (sequence step 1)
  2. Update vCloud Networking and Security (vShield Manager) (sequence step 2)
  3. Update vCenter Server (sequence step 5)
  4. Update ESXi (sequence step 7)
  5. Update vShield Edge (sequence step 9)

Example 2

If you have SRM solution installed in your environment, the supported patch update sequence is:

  1. Update vCenter Server (sequence step 5)
  2. Update vSphere Replication (sequence step 6)
  3. Update ESXi (sequence step 7)

Example 3

If you have the vSphere Data Protection solution installed in your environment, the supported patch update sequence is:

  1. Update vCenter Server (sequence step 5)
  2. Update vSphere Data Protection (sequence step 6)
  3. Update ESXi (sequence step 7)

Example 4

If you have the vSphere Storage Appliance solution installed in your environment, the supported patch update sequence is:

  1. Update vSphere Storage Appliance Manager (sequence step 4)
    1. For a 2 node VSA cluster, see Upgrade a Two-Node VSA Environment in the vSphere Storage Appliance Installation and Administration guide
    2. For a 3 node VSA cluster, see Upgrade a Three-Node VSA Environment in the vSphere Storage Appliance Installation and Administration guide
  2. Update vCenter Server (sequence step 5)
  3. Update vSphere Storage Appliance Cluster (sequence step 6)

Example 5

If you have a Cisco Nexus 1000V virtual distributed switch solution installed in your environment, the supported patch update sequence is:

  1. Verify with Cisco the compatibility for the Nexus upgrade procedure. This will dictate the order for upgrading the vCenter Server and the ESXi hosts.
  2. Update vCenter Server (sequence step 5)
  3. Update ESXi (sequence step 7)

Note: If you are using the vSphere Client in your environment, VMware recommends that you upgrade the vSphere Client to version 5.5.

vSphere 5.5 and its compatible VMware products

This table provides information about the current version of released VMware products and the recommended action required to patch to the next level. The table also provides reference links to release notes and update procedure documents.

vSphere 5.5 and its compatible VMware products

Product Version Recommended Action Important Links
vCloud Director (VCD) 5.5.0 Update to 5.5.0 Release Notes
Update Procedure
vCloud Networking and Security (VCNS) 5.5.0 Update to 5.5.0 Release Notes
Update Procedure
Horizon View (View) 5.2.0 Update to 5.2.0 Release Notes
Update Procedure
vCenter Server 5.5.0 Update to 5.5.0 Release Notes
Update Procedure
vSphere Replication (VR) / vCenter Site Recovery Manager (SRM) 5.5.0 Update to 5.5.0 VR Release Notes
SRM Release Notes
Upgrading VR
Upgrading VR without internet access
Upgrading SRM
vCenter Operations Manager (vCOPS) 5.7.2 Update to 5.7.2 Release Notes
Update Procedure
vSphere Data Protection (VDP) 5.5.1 Update to 5.5.1 Release Notes
Update Procedure
vSphere Storage Appliance (VSA) 5.5 Update to 5.5 Release Notes
Update Procedure
ESXi 5.5.0 Update to 5.5.0 Release Notes
Update Procedure
vShield Edge 5.5.0 Update to 5.5.0 Release Notes
Update Procedure
vShield App 5.5.0 Update to 5.5.0 Release Notes
Update Procedure
vShield Endpoint 5.5.0 Update to 5.5.0 Release Notes
Update Procedure

Troubleshooting VMware snapshots

Post source techtarget

Virtualization administrators can use snapshots in vSphere to travel back in time and figure out what went wrong with their virtual machines (VMs). In part one of this series, I discussed how to use VMware snapshots. In part two, I explained how to delete snapshots without wasting disk space. But what do you do when your snapshots start acting funny? In this tip, we’ll troubleshoot potential problems that may come up when using snapshots in vSphere.

Locating VMs that have snapshots
Finding out which VMs have snapshots can be challenging. In VMware Infrastructure 3, there wasn’t a centralized, built-in way to accomplish this task in the vSphere Client or vCenter Server. You had to use methods, such as scripts and command-line utilities, that made locating snapshots difficult. But there were some enhancements in vSphere that made locating snapshots much easier. Here are a few of the methods that you can use.

Method 1: Find command
Use the find command in the ESX service console or ESXi Tech Support Mode

  1. Log in to the console.
  2. Change to your /vmfs/volumes/ directory.
  3. Type find -iname “*-delta.vmdk” -mtime +7 -ls to find snapshot files that have not been modified in seven days or simply find -iname “*-delta.vmdk” to find all snapshot files.

Method 2: Use the Storage View in vCenter Server
The Storage View, part of a new Storage Monitoring and Reporting plug-in that comes with vCenter Server, shows information related to storage in vSphere. When you select an object in the left pane of the vSphere Client, you can select the Storage View tab in the right pane and view storage information related to that object. One of the columns that you can view is Snapshot Space — which is the total size of all snapshot-related files, including the -delta.vmdk, .vmsd and .vmsn files.

By selecting an object, such as Cluster or Datacenter, and sorting the Snapshot Space field, you can view the size of any VM snapshot that exists under that object. VMs that haven’t had a snapshot will show 0 bytes. Once a snapshot of a VM is taken, it will still show a very small size (around 40 bytes), which is from the residual text left in the .vmsd file.

Method 3: Use alarms in vCenter Server
You can configure a vCenter Server alarm to trigger when a VM snapshot size reaches a predetermined gigabyte threshold. You can also set alarms at any virtualization level — from a single VM to the top vCenter Server level. These alarms will keep you informed of snapshot growth, so you can take action, if needed.

Method 4: Use a PowerShell script
The Get-Snapshot command, part of vSphere PowerCLI, can query VM snapshot information. You can use it in scripts to produce reports on VMs that have active snapshots. There are several, free PowerShell scripts that you can download and run periodically, such asSnapReminderyadr — A vdisk reporter and Snapshot List. You can also set the scripts to run automatically.

Dealing with snapshots that don’t delete properly
Occasionally, a snapshot will not delete properly, leaving an active snapshot for a VM. This situation can happen when using backup applications or deleting snapshots through Snapshot Manager. In most cases, the snapshot will not appear in the Snapshot Manager. The only indication that a snapshot may still exist is the presence of delta files in the VM’s directory.

If you have a snapshot running that is not in Snapshot Manager, you can attempt to delete it in one of two ways. First, create a new snapshot using the vSphere Client and delete all snapshots from the snapshot manager after the new one has been created. Alternatively, use the ESX service console or vSphere CLI. Switch to the VM’s home directory and create a new snapshot by typing vmware-cmd createsnapshot . Wait for the snapshot to be created and type vmware-cmd removesnapshots. When it completes, see if the delta files have been deleted. If they have, then it was successfully completed.

If the delta files weren’t deleted, check the VMX file for the VM and locate the lines starting with scsi. If the VM is configured with only one virtual disk, it is usually scsi0:0. (If .present is false, it is a non-existent drive that you can ignore.) The .fileName should be using the original disk file that was created with the VM and it’s usually the same name as your VM. If this is the case, then your VM is not using the snapshot files. If it has a -00000# in the filename, it is currently using a snapshot file.

To be clear, a VM with no snapshots displays the following: scsi0:0.present = “true” scsi0:0.fileName = “myvmname.vmdk”. And a VM with snapshots will display the following: scsi0:0.present = “true” scsi0:0.fileName = “myvmname-000001.vmdk”

If the above operation failed, your other options are to either clone the VM or clone the VM’s disk file. To clone the VM, you can either use the clone function in vCenter Server or the standalone vCenter Converter application. When it’s completed, shut down and delete the old VM.

Another method is to shut down the VM. Log in to the ESX Service Console or ESXi Tech Support Mode. Then, switch to the VM’s directory and clone the VM’s disk file, using vmkfstools and specifying the snapshot file as the source disk (i.e. “vmkfstools –i myvmname-000001.vmdk myvmnamenew.vmdk”).

Next, go into the settings for the VM. Remove (don’t delete) the hard disk. Then, add a new hard disk and browse to the newly created disk file. Power on the VM and verify everything is working before you delete the old disk and delta files.

Changing snapshot file locations
By default, the snapshots are written to the home directory of each virtual machine. You may want to change this location, as to not take up space on the volume that your VM resides. It is possible to individually specify a new working directory for snapshots on each VM. Both snapshots and .vswp files are written to this directory when you choose this method.

Be warned: If the VM is on shared storage and you specify local storage as a location, you will not be able to use features that move VMs between hosts, such as vMotion, High Availability and Distributed Resource Scheduler. To do this, follow these steps:

  1. Power off your VM and log in to the ESX service console or ESXi Tech Support Mode.
  2. Edit the VMX file of your VM with the nano (ESX only) or vi (ESX/ESXi) editor.
  3. Add a new line, using the following syntax: workingDir=”/vmfs/volumes/SnapVolume/Snapshots/”
  4. If you want your .vswp file to stay in the VM’s directory, add the following line to the VMX file: sched.swap.dir = “/vmfs/volumes/VM-Volume1/MyVM/”. This step is optional. Furthermore, do not worry about updating the existing “sched.swap.derivedName” parameter, because it is generated by the VM and written to the configuration file each time the VM powers on.
  5. Power on your VM, and your .vswp, .vmsn and snapshot (delta-vmdk) files will now be located in this directory.

Using vMotion and Storage vMotion with snapshots
Using vMotion to migrate a VM to a different host is supported and all existed snapshots are retained. If you try to vMotion a VM with running snapshots from one host to another, however, you will receive the following warning: “Reverting to snapshot would generate error (warnings) on the destination host.” In other words, the migration wizard cannot verify the compatibility of the virtual machine state in the snapshot with the destination host.

Because the compatibility cannot be verified, a failure could occur if the VM configuration in the snapshot uses devices or virtual disks that are not accessible on the destination host. A failure can also occur if the snapshot contains an active VM state that was running on virtual hardware and it’s incompatible with the destination host CPU.

Using Storage vMotion to move a VM to another disk location is not supported, initially. To use it, you must first delete all the snapshots on a VM. Alternately, you can power the VM off and perform a cold migration to another disk location.

Using Fault Tolerance with snapshots
VM snapshots are not supported on VMs that use Fault Tolerance (FT). As a result, backing up FT-enabled VMs can be tricky, because many backup applications rely on VM snapshots.

Look at alternative backup methods, such as traditional OS backup agents that run inside the VM, cloning VMs and then backing up the clones, temporarily disabling FT when running backups on the VM or using storage snapshots to backup the VM’s data store.

Fault Tolerance can be controlled via PowerShell scripts, so you can run pre-backup scripts to temporarily disable FT. That way, a backup application can take a snapshot. Then, a post-backup script can re-enable FT.

Understanding the files that make up a VMware virtual machine

Post source techtarget

VMware admins should know the components of virtual machines. Understanding the files that make up a virtual machine can help admins decide what files are unnecessary and clean them out, and ease other management tasks.

Once you understand virtual machines (VMs) from a hardware perspective, you can study the components that make up a VM on an ESX/ESXi host. These are the various VMware file types associated with a VM, located in the VM’s directory on the host (represented in the illustration below).

 

VMware virtual machine files are organized in the Virtual Machine File System (VMFS). If you look at the list of files associated with the VM — use an SCP-based tool or follow VMware’s recommendations — you’ll notice that most of the files start with the actual name of the VM, followed by different file extensions that denote the file type. You may not see all of the possible file types in the VMFS until your VM is in a certain state. For example, the .vswp file is only present when the VM is powered on and the .vmss file is only present when a VM is suspended. Below is a typical VM directory listing (using WinSCP).

So what are all these VMware file types and what are they used for? Here’s each file type in detail.

The .nvram file. This small file contains the BIOS that is used when the VM boots. It is similar to a physical server that has a BIOS chip that lets you set hardware configuration options. A VM also has a virtual BIOS that is contained in the NVRAM file. The BIOS can be accessed when a VM first starts up by pressing the F2 key. Whatever changes are made to the hardware configuration of the VM are then saved in the NVRAM file. This file is in binary format and if deleted it will be automatically re-created when a VM is powered on.

The .vmx file. This file contains all of the configuration information and hardware settings of the virtual machine. Whenever you edit the settings of a virtual machine, all of that information is stored in text format in this file. This file can contain a wide variety of information about the VM, including its specific hardware configuration (i.e., RAM size, network interface card info, hard drive info and serial/parallel port info), advanced power and resource settings, VMware tools options, and power management options. While you can edit this file directly to make changes to a VM’s configuration, don’t do this unless you know what you are doing. If you do make changes directly to this file, make a backup copy first.

VMDK files. All virtual disks are made up of two files, a large data file equal to the size of the virtual disk and a small text disk descriptor file, which describes the size and geometry of the virtual disk file. The descriptor file also contains a pointer to the large data file as well as information on the virtual disks drive sectors, heads, cylinders and disk adapter type. In most cases these files will have the same name as the data file that it is associated with (i.e., myvm_1.vmdk and myvm_1-flat.vmdk). You can match the descriptor file to the data file by checking the Extent Description field in this file to see which -flat, -rdm or -delta file is linked to it. 

The different types of virtual disk data files that can be used with VMware virtual machines are:

  • The -flat.vmdk file
    This is the default large virtual disk data file that is created when you add a virtual hard drive to your VM that is not an RDM. When using thick disks, this file will be approximately the same size as what you specify when you create your virtual hard drive. One of these files is created for each virtual hard drive that a VM has configured, as shown in the examples below.

     

  • The -delta.vmdk file
    These virtual disk data files are only used when making snapshots. When a snapshot is created, all writes to the original -flat.vmdk are halted and it becomes read-only; changes to the virtual disk are then written to these -delta files instead. The initial size of these files is 16 MB and they are grown as needed in 16 MB increments as changes are made to the VM’s virtual hard disk. Because these files are a bitmap of the changes made to a virtual disk, a single -delta.vmdk file cannot exceed the size of the original -flat.vmdk file. A delta file will be created for each snapshot that you create for a VM and their file names will be incremented numerically (i.e., myvm-000001-delta.vmdk, myvm-000002-delta.vmdk). When the snapshot is deleted, these files are automatically deleted after they are merged back into the original flat.vmdk file.

     

  • The -rdm.vmdk file
    This is the mapping file for the raw device mapping (RDM) format that manages mapping data for the RDM device. The mapping file is presented to the ESX host as an ordinary disk file, available for the usual file system operations. However, to the VM, the storage virtualization layer presents the mapped device as a virtual SCSI device. The metadata in the mapping file includes the location of the mapped device (name resolution) and the locking state of the mapped device. If you do a directory listing, you will see that these files will appear to take up the same amount of disk space on the VMFS volume as the actual size of the LUN that it is mapped to, but in reality they just appear that way and their size is very small. One of these files is created for each RDM that is created on a VM.

The .vswp file. When you power on a VM, a memory swap file is created that can be used in lieu of physical host memory if an ESX host exhausts all of its physical memory because it isovercommitted. These files are created equal in size to the amount of memory assigned to a VM, minus any memory reservations (default is 0) that a VM may have set on it (i.e., a 4 GB VM with a 1 GB reservation will have a 3 GB VSWP file created). These files are always created for virtual machines but only used if a host exhausts all of its physical memory. As virtual machine memory that is read/written to disk is not as fast as physical host RAM, your VMs will have degraded performance if they do start using this file. These files can take up quite a large amount of disk space on your VMFS volumes, so ensure that you have adequate space available for them, as a VM will not power on if there is not enough room to create this file. These files are deleted when a VM is powered off or suspended.

Virtual machines will lock the .vswp, -flat.vmdk and -delta.vmdk, .vmx and .log files during runtime.

The .vmss file. This file is used when virtual machines are suspended and is used to preserve the memory contents of the VM so it can start up again where it left off. This file will be approximately the same size as the amount of RAM that is assigned to a VM (even empty memory contents are written). When a VM is brought out of a suspend state, the contents of this file are written back into the physical memory of a host server, however the file is not automatically deleted until a VM is powered off (an OS reboot won’t work). If a previous suspend file exists when a VM is suspended again, this file is re-used instead of deleted and re-created. If this file is deleted while the VM is suspended, then the VM will start normally and not from a suspended state.

The .vmsd file. This file is used with snapshots to store metadata and other information about each snapshot that is active on a VM. This text file is initially 0 bytes in size until a snapshot is created. A VMSD file updates with information every time snapshots are created or deleted. Only one of these files exists regardless of the number of snapshots running, as they all update this single file. The snapshot information in a VMSD file consists of the name of the VMDK and VMSN file used by each snapshot, the display name and description, and the UID of the snapshot. Once your snapshots are all deleted, this file retains old snapshot information but increments the snapshot UID to be used with new snapshots. It also renames the first snapshot to “Consolidate Helper,” presumably to be used with consolidated backups.

The .vmsn file. This file is used with snapshots to store the state of a virtual machine when a snapshot is taken. A separate .vmsn file is created for every snapshot that is created on a VM and is automatically deleted when the snapshot is deleted. The size of this file will vary based on whether or not you choose to include the VM’s memory state with your snapshot. If you do choose to store the memory state, this file will be slightly larger than the amount of RAM that has been assigned to the VM, as the entire memory contents, including empty memory, is copied to this file. If you do not choose to store the memory state of the snapshot then this file will be fairly small (under 32 KB). This file is similar in nature to the .vmss that is used when VMs are suspended.

The .log file. LOG files are created to log information about the virtual machine and are often used for troubleshooting purposes. There will be a number of these files present in a VM’s directory. The current log file is always named vmware.log and up to six older log files will also be retained with a number at the end of their names (i.e., vmware-2.log). A new log file is created either when a VM is powered off and back on or if the log file reaches the maximum defined size limit. The amount of log files that are retained and the maximum size limits are both defined as VM advanced configuration parameters (log.rotateSize and log.keepOld).

The .vmxf file. This file is a supplemental configuration file that is not used with ESX but is retained for compatibility purposes with VMware Workstation. It is in text format and is used by Workstation for VM teaming where multiple VMs can be assigned to a team so they can be powered on or off, or suspended and resumed as a single object.

[Editor’s note: Article update in April 2013]

The .ctk file. VMware CTK files list any changes made to the VM between backups. This file describes the VMDK block and grows in proportion with the number of VMDK blocks. There is one CTK file per VMDK. Change tracking files originated with VMware’s Changed Block Tracking (CBT) technology for incremental backups. The CTK file stores information about what VM information blocks changed, avoiding unnecessary block backups. VMware snapshots also use .ctk files. Like .log and .nvram files, .ctk files are small. 

Other less-frequently seen file types include the .vmem virtual machine paging file and the .vmtm configuration file for team data. Like VMSN files, VMEM files back up a virtual machine’s memory. They exist when the VM is running or in the event of a VM crash. VMTM files support VM teams, a feature in VMware Workstation that allows a group of VMs to work together via a private LAN segment.

That covers all the files that are associated with a VMware VM, and you should have a better understanding of VM anatomy. Check out the VMs on your own VMware hosts to see the various files that make up these virtual machines. You might find a few surprises from old data that has not been properly cleaned up on VMFS volumes. Just be careful before you start deleting any files and make sure that the files you delete are no longer needed and not being used.

 

In Short and Brief

.VMDK — These files are the actual hard disk of the virtual machine itself, and tend to be the largest file within the folder. You can consider the size of this file to be roughly equivalent to the size of either the disk itself (if you’ve chosen to use preallocated disks) or the size of the data currently stored on that disk (if you use growable disks).

.NVRAM — Consider this file the BIOS of the virtual machine.

.VMX — With typically one VMX file per folder, this file holds the configuration information for the virtual machine in a text format. 

Unlike almost all the other files you’ll see, these files can be edited using any text editing program, a process that is actually required for some functionality that is not exposed in the GUI.

.VMXF — This file, in XML format, includes additional information about the virtual machine if it has been added to a team. If a machine has been added to a team and then later removed, this file remains resident. This file can also be opened and read in a text editor.

.VMTM — For virtual machines actively participating in a team, this file stores information about that team membership.

.VMEM — These files, which contain a backup of the VMs paging file, are typically very small or non-existent when the virtual machine is powered off, but grow immediately to the size of configured RAM when the machine is powered on.

.VMSN and .VMSD — When snapshots are created for a virtual machine, these files are created to host the state of the virtual machine. 

The VMSN file stores the running state of the machine, what you could consider the “delta” between the VMDK at the point of the snapshot and what has been processed up until the present time. The VMSD stores information and metadata about the snapshot itself.

.VMSS — If you’ve suspended the state of your machine, this file contains the suspended state of that machine. These files typically only appear when virtual machines have been suspended. 

.HLOG — If you have vMotioned the Virtual Machine, this file is created and can be safely deleted.

vCenter and Memory metrics

vCenter and Memory metrics
Post source avirtualworldblog

There are a couple of places where memory details are shown on a “VM level” within the vCenter client. The first tab that we will discuss is the Summary tab. It shows “General” and “Resources”. It appears that there is a lot of confusion around this topic and that probably comes from the fact that some of the Performance Metrics are named similarly but don’t always refer to the same.

Lets start with “General”:

In the screenshot above you can see 2 fields related to memory:

Memory (2048MB)
Memory Overhead (110.63MB)

The first one, Memory, is an easy one. This is the amount of memory you provisioned your VM with, in this case 2048MB. The second field is Memory Overhead. Memory Overhead is the amount of memory the VMkernel thinks it will need to run the virtualized workload, in this case 110.63MB. This typicall would include things like page tables, frame buffers etc.

That brings us to the Resources sections:

This section shows again two fields related to memory:

Consumed Host Memory (1390.00MB)
Active Guest Memory (61.00MB)

Consumed and Active is where it becomes a bit less obvious but again it isn’t rocket science.Consumed Host Memory is the amount of physical memory that has been allocated to the virtual machine. This also includes things like memory overhead, that also means that Consumed can be larger than what has been provisioned. To make it a bit more complex it should be noted that in the “Performance Tab” the “Consumed” Counter doesn’t actually include Memory Overhead!

Active Memory more or less already explains it, it is what the VMkernel believes is currently being actively used by the VM. Now it should be pointed out here that this is an estimate calculated by a form of statistical sampling.

The second tab that contains details around memory is “Resource Allocation”. Looking at the tab I guess it is obvious that this one contains more details and is more complex than the summary tab:

The Memory section contains three sub-sections and I have carved them up as such:

The first section is the host memory:

Consumed (1.36GB)
Overhead Consumption (42.00MB)

Again, Consumed is the amount of machine memory currently allocated to the VM. In other words, out of the 2GB provisioned currently 1.36GB is being consumed by that VM. The Overhead Consumption is the amount of memory being consumed for the virtualization overhead, as you can see it is less than what the VMkernel expected to use as mentioned in the first screenshot. I guess you could do the math easily:
Consumed = Private + Overhead Consumption

Guest Memory

Private (1.32GB)
Shared (700.00MB)
Swapped (0.00MB)
Compressed (0.00MB)
Ballooned (0.00MB)
Unaccessed (1.00MB)
Active (102.00MB)

This is the part where it gets slightly more complicated. Private is the amount of memory that is physically backed by the Host. In other words 1.32GB is physically stored. Shared is the total amount of memory shared by TPS. Swapped, Compressed and Ballooned speak for itself in my opinion but lets be absolutely clear here. Swapped the amount of memory reclaimed by VMkernel swapping, Compressed is the amount of memory stored in the VMs compression cache andBallooned is the amount of memory reclaimed by the Balloon Driver. Ultimately all of these should be 0.

There’s one which I couldn’t really explain which is Unaccessed. The documentation describes it as “the amount of memory that has never been referenced by the guest”. Active is the amount of memory actively used, again it is an estimate done by statistical sampling. (Did you notice it changed from 61MB to 102MB.)

The last section is Resource Settings, I guess most are obvious (like Reservation, Limit, Configured, Shares) but the two that might not be are:

Worst Case Allocation (2.14GB)
Overhead Reservation (0.00MB)

Worst Case Allocation is the amount of memory that the virtual machine can allocate when ALL virtual machines consume the full amount of allocated resources. Basically when there is severe overcommitment this is what the VM will get in the worst possible case. This is also one of the key metrics to keep an eye on in my opinion. Especially when you are over-committing and over-provisioning your systems this metric will be a key-indicator. Overhead Reservation is the amount of Overhead Memory reserved, not much to say about that one.